c ole instrument corporation is proud to offer a rotary switch with illumination through the end of the shaft front. this can be used to light up any part of the rotary switch?s knob. an led (light emitting diode) or an incandescent lamp is on the back end of the switch body, and a light pipe or fiber optics brings the concentrated light through the switch to the shaft front. the series ip3900 and is3900 switch offers maximum and optimum visibility at sunlight with minimum power levels. and at night, there is zero light leakage through the length of the switch. light can meet most chromaticity or intensity requirements. the light can be an led or a t1 incandescent lamp. the switch features good heat sinking capabilities, and delivers up to twice the light intensity of units at equivalent power levels. on light failure, reclamping can be done by the customer. cole can provide the replacement assembly. this switch can be used in airborne, shipboard, and submarine panel control displays and meets the brightness requirements of high altitude aircraft, as well as the mil-s-901c shock requirement for submarines and ships. ip3900 & is3900 series illuminated shaft, one inch diameter body iso9001 certified
ip3900 & is3900 series ip3900 & is3900 series illuminated shaft, one inch diameter body 2650 south croddy way p.o. box 25063 santa ana, california 92799-5063 usa phone 714.556.3100 sales fax 714.241.9061 www.cole-switches.com iso9001 certified ip3900 & is3900 series/page 2 ip3900 illuminated switch (see page 3) note: ip3900 illuminated switch - .250 shaft dia., .375 ferrule dia., .688 body dia., (see page 3). is3900 illuminated switch - .250 shaft dia., .375 ferrule dia., .688 body dia., (see page 4). is3900 illuminated switch (see page 4)
ip3900 & is3900 series ip3900 & is3900 series illuminated shaft, one inch diameter body 2650 south croddy way p.o. box 25063 santa ana, california 92799-5063 usa phone 714.556.3100 sales fax 714.241.9061 www.cole-switches.com iso9001 certified ip3900 & is3900 series/page 3 notes: 1. dimensions are in inches. 2. unless otherwise speci ed, tolerances are .02 and 2 on angles. 3. switch shall be marked with cole p/n, cage code, date code and terminal identi cation. 4. mounting hardware shall consist of one (1) hex nut, iaw ms25082, one (1) internal tooth lock washer, iaw ms35333, and one (1 ) non-turn key washer. 5. switch can have up to six (6) decks. add 0.220 to the length for each additional deck. 6. optional 0.432 non-turn key washer available. 7. switch shown is with an led for illumination. for incandescent lamp application, contact factory. ordering information sample code switch shown in the sample code is 30 indexing, 1 pole per deck, 12 positions per pole, 1 deck with shorting type contact. options the following options can be added to the standard switch. when ordering, simply add the letters after the basic part number. a = adjustable stops (special, extra charge). f = fixed stops between the rst and last position on a full-turn switch. g = rfi-emi shielding. l = low level. p = panel and shaft seals. s = shorting (available in all con gurations). y = optional .432 non-turn washer. screw terminals available. (contact factory for special part number) view a mounting bushing washer high performance t-1 led lamp mounting hole
ip3900 & is3900 series ip3900 & is3900 series illuminated shaft, one inch diameter body 2650 south croddy way p.o. box 25063 santa ana, california 92799-5063 usa phone 714.556.3100 sales fax 714.241.9061 www.cole-switches.com iso9001 certified view a notes: 1. dimensions are in inches. 2. unless otherwise speci ed, tolerances are .02 and 2 on angles. 3. switch shall be marked with cole p/n, cage code, date code and terminal identi cation. 4. mounting hardware shall consist of one (1) hex nut, iaw ms25082, one (1) internal tooth lock washer, iaw ms35333, and one (1 ) non-turn key washer. 5. switch can have up to six (6) decks. add 0.220 to the length for each additional deck. 6. optional 0.432 non-turn key washer available. 7. switch shown is with an led for illumination. for incandescent lamp application, contact factory. ordering information sample code switch shown in the sample code is 30 indexing, 1 pole per deck, 12 positions per pole, 1 deck with shorting type contact. options the following options can be added to the standard switch. when ordering, simply add the letters after the basic part number. a = adjustable stops (special, extra charge). f = fixed stops between the rst and last position on a full-turn switch. g = rfi-emi shielding. l = low level. p = panel and shaft seals. s = shorting (available in all con gurations). y = optional .432 non-turn washer. screw terminals available. (contact factory for special part number) recommended panel cutout high performance t-1 led lamp ip3900 & is3900 series/page 4
ip3900 & is3900 series ip3900 & is3900 series illuminated shaft, one inch diameter body 2650 south croddy way p.o. box 25063 santa ana, california 92799-5063 usa phone 714.556.3100 sales fax 714.241.9061 www.cole-switches.com iso9001 certified ip3900 & is3900 series/page 5
|
